An anchor sitting in its hawse pipe looks secured. By that fact alone it is not. The rules keep housing geometry, chain lead, anchor lashing and chain stopper in separate clauses, each answering a different question [1][2]. The pipe must let the anchor seat and let the chain run without being bent over a hard edge; the lashing must hold the anchor against a stated design load [1]; the stopper, where fitted, secures the chain rather than the anchor [1][2]. Which of them a drawing or a trial record should settle is what follows.
What "stowed" means in the rules
The CSR require two bower anchors connected to chain cable and stowed in position ready for use [1]; IACS UR A1 puts it more compactly — positioned on board, connected to their cables [3]. Ready for use is two conditions: the anchor is on board, and it is connected in its stowage position. An anchor in a pocket with its cable disconnected does not meet it, and neither does a cable ranged on deck.
The hawse-pipe clause is narrower than it is usually read to be. It requires the position and slope of the pipes to create an easy lead for the chain cables and efficient housing for the anchors, avoiding damage to the hull [1], then adds a sentence easy to miss: where hawse pipes are not fitted, alternative arrangements will be specially considered [1]. The clause addresses ships that have a pipe and leaves the rest to individual assessment; the geometry below is the common case.
One scope note covers every number here: the numerical clauses come from CSR, which cover bulk carriers and oil tankers, and from LR's rules for ships [1][2]. Other rule sets differ — LR's special service craft rules handle anchor stowage separately, with local protection for a stemhead-mounted anchor and no hawse-pipe or stopper load clauses.
The pocket and hawse pipe: geometry that lets the anchor sit
An anchor that will not seat may be a geometry problem before it is a handling problem, and the rules state geometry as performance, not dimensions. Hawse pipes are to be of suitable size and configuration to ensure adequate clearance and an easy lead of the chain cable from the chain stopper through the ship's side, and of sufficient strength; chafing lips of suitable form, with ample lay-up and a radius adequate to the chain cable, go at shell and deck, with the shell plating reinforced as necessary [1]. The lead runs from the stopper, not the windlass [1].
LR adds the pocket: pipes and pockets are to be of ample thickness and a suitable size and form to house the anchors efficiently, preventing, as much as practicable, slackening of the cable or movement of the anchor from wave action [2]. That qualifier is part of the requirement.
The one geometric criterion given is a bearing condition. Pipes and pockets need full-rounded flanges or rubbing bars to minimise the nip on the cables and high bending stress in the links, with a radius of curvature such that at least three links of chain bear simultaneously on the rounded parts of the upper and lower ends, where the chain is supported while paying out, hoisting and at anchor [1]. That is a condition on how the chain sits, not a dimension: no pocket depth, opening angle or clearance is given, and three links bearing is checked against the chain specified and the pipe drawn.
Read together, the clauses give four jobs:
| Job | What it decides | Where the rule puts it |
|---|---|---|
| Seat the anchor | Pipe and pocket size, form and thickness; wave-action movement limited as far as practicable | CSR 3.8.1 [1]; LR 8.12.3 [2] |
| Lead the chain | Clearance and easy lead from the stopper through the ship's side; end radii keeping three links bearing | CSR 3.8.1, 3.8.3 [1] |
| Lash the anchor | Twice the anchor mass plus 10 m of cable, within 40% of the yield strength of the lashing material | CSR 3.5.3 [1] |
| Secure the chain | 80% of the chain breaking load without permanent deformation, on its own supporting structure | CSR 3.6.1–3.6.2 [1]; LR 8.12.2 [2] |
Four jobs, four clauses, and no one of them secures the anchor alone.
The lashing: what it has to resist
Anchor lashings are to be designed to resist a load at least corresponding to twice the anchor mass plus 10 m of cable, without exceeding 40% of the yield strength of the lashing material [1].
Two figures do different work: the first sets the load the arrangement resists — twice the anchor mass plus the mass of 10 m of cable; the second caps the stress the material may see while resisting it, at 40% of yield. A lashing satisfying one and not the other does not satisfy the clause, and a catalogue tensile figure answers neither: the load is read from the anchor mass and the cable's mass per metre, the check from the material's yield strength.
It is a design load on the lashing, not a demonstration of holding capacity: anchoring equipment is intended for temporary mooring in a harbour or sheltered area, and assumes one bow anchor and one chain cable at a time [5], and a stowage lashing shares that premise.
The clause names no fitting; it states a load and a stress limit, leaving the form to the designer [1]. Wärtsilä defines a devil's claw as a stretching screw with two heavy hooks or claws, used to secure an anchor in a hawse pipe [4]. That is one implementation, and a recognisable one, but not a requirement: a different tensioned arrangement meeting the load and stress conditions meets the clause on the same terms.
The chain stopper's share
The stopper is not the lashing under another name; the rules keep them apart. Chain stoppers are to secure each chain cable once it is paid out, and their securing arrangements are to withstand a load equal to 80% of the breaking load of the chain cable without permanent deformation [1]. LR requires ductile stoppers designed to minimise damage to or snagging of the cable, and states the same 80% against the rule breaking load [2]. They are drafted differently and should not be merged: the 80%, the condition and the subject are common to both.
The 80% is a design load on that securing arrangement, not a product certification grade — what the structure must withstand, not that a fitted product is rated to that level. The case closes against the chain fitted and the structure drawn; a listing shows a fitting is offered, not approved.
It carries its own structure: the securing arrangement is checked with its own supporting structure, which is why it is a fitting in its own right, not a windlass part and not a brake — it secures a chain already paid out [1][2].
The lashing holds the anchor against the hull or in the pocket; the stopper holds the chain. Neither compensates for an anchor that does not seat.
What the trials check
The on-board test is where stowage is verified. Each unit is to be independently tested for braking, clutch functioning, lowering and hoisting of the chain cable and anchor, proper riding of the chain over the cable lifter, proper transit through the hawse pipe and the chain pipe, and proper stowage of the chain and anchor; LR adds confirmation that anchors properly seat in the stored position and that chain stoppers function as designed, if fitted [2]. The CSR trial lists the same windlass items but does not add the anchor-seating or stopper-function confirmation [1].
In the LR list, three items are stowage items: transit through the pipe, stowage of chain and anchor, and seating in the stored position. An anchor that fouls its pocket or a pipe that nips the chain will show up here, on the gear that goes to sea.
The record is bounded: on that day, with that anchor, chain and pipe, the anchor seated and the stopper functioned as designed — not evidence about a sea state outside the trial condition.
What the drawings and documents should show
The clauses give a short document set:
| Document | What it should settle |
|---|---|
| Stowed outline, in the pocket or against the shell | Where the anchor sits, and how much stands proud of the hull |
| Hawse pipe and pocket drawing | Clearance and lead from the stopper through the ship's side; end radii that keep three links bearing |
| Chain route from stopper to windlass | Where the cable is supported, and where it changes direction |
| Lashing arrangement and attachment points | Whether the lashing load has a path into structure rather than into a fairing |
| Stopper arrangement and supporting structure | Whether the 80% case sits on its own structure, separate from the windlass foundation |
| Trial record | Whether the anchor seated and the stopper functioned with the gear fitted |
Dimensions are read from the ship, not from an article; no clause quoted here supplies a pocket depth, opening angle or clearance value.
The stowed outline is a design characteristic, not a universal shape, so fit is checked per vessel: the stockless anchor article covers how anchor and pocket must suit one another, the Hall anchor article shows the outline a named design needs, and the anchoring system article treats the pipe as a passage, not a load-bearing part.
What to send before an RFQ
Five items let a supplier read the arrangement against one ship:
- The anchor drawing and its stowed outline.
- The hawse pipe and pocket drawing, or the arrangement drawing where no pipe is fitted.
- The chain size and grade, with its breaking load.
- The stopper arrangement and its supporting structure, or a statement that none is fitted.
- The rule set and edition that apply to the vessel.
Items 3 and 4 decide what the 80% and the 40% are percentages of. Where the anchor is being replaced rather than the stowage reworked, the interface checks are in the anchor replacement article; the anchor range is on the marine anchor page and the stopper on the marine chain stopper page.
Send the five items with the enquiry so that anchor, pipe, chain and stopper are read as one arrangement, not four quotations.
References
[1] IACS, Common Structural Rules for Bulk Carriers and Oil Tankers, January 2019, Part 1 Ch 11 Sec 3 — https://www.imorules.com/GUID-AC6535E2-4B3B-4E12-AB63-C3D0F72E4FCA.html
[2] Lloyd's Register, Rules and Regulations for the Classification of Ships, July 2022, Pt 3 Ch 13 Sec 8 — https://www.imorules.com/LRSHIP_PT3_CH13_8.html
[3] IACS, UR A1 — Anchoring Equipment, Rev.7 2020/Corr.1 2021 — https://ww2.eagle.org/content/dam/eagle/regulatory-news/2022/IACS-UR-A1.pdf
[4] Wärtsilä Encyclopedia, "Devil's claw" — https://www.wartsila.com/encyclopedia/term/devil-s-claw
[5] Wärtsilä Encyclopedia, "Anchor" — https://www.wartsila.com/encyclopedia/term/anchor


