A windlass is a machine for winding and unwinding the anchor chain, not a winch with an anchor on the end of it [3]. Its size is written as a chain diameter, a chain grade and a holding-load percentage [1]. Its brake is rated against the breaking load of a named chain, not against motor power [1][2]. And what the brake must hold depends on whether a chain stopper is fitted: 45% with a stopper, 80% without [1][2].
Two documents can call the same windlass a 45% brake and an 80% brake and both be right; what resolves them is size designation, stopper condition and test record.
What the size designation tells you
The nominal size is expressed as chain cable diameter in millimetres, grade of chain cable and holding load [1]. The standard's example is 100/3/45: a windlass for 100 mm chain of IACS Grade 3, with a holding load of 45% of the breaking load of that chain [1].
| Field | Example | What it ties the windlass to |
|---|---|---|
| Chain cable diameter | 100 | 100 mm nominal chain; the cable lifter is socketed for it [3]. |
| Chain grade | 3 | The grade of the chain. LR writes the same field as the numeral in steel grade U3 [2]. |
| Holding load | 45 | A percentage of that chain's breaking load: what the brake is rated to hold [1]. |
The third field is the one read wrongly: it is the basis on which the brake is rated, a percentage of one chain's breaking load — not the chain grade again, not a mass. A 100/3/45 windlass is not a 45-tonne windlass. Holding load is the maximum static load on the chain that the cable-lifter brake can withstand [1]; without the chain, the percentage means nothing.
The grade field belongs to the chain, and it is set out in the chain grade article.
The copy of ISO 4568 read here is the 2006 edition; BV NR626 prints ISO 4568:2021 as an acceptable recognised standard, so the 2006 text is not current. Confirm the edition named in the contract [1][3].
Cable lifter, brake, clutch: three different jobs
- The cable lifter is the socketed wheel fitted on the windlass to receive and drive the chain, and it must be declutchable from the drive [3]. The rule texts read here say cable lifter or chain lifter [3][4]; a drawing marked wildcat, or a catalogue saying gypsy, is using trade language rather than the rule term.
- The brake holds: each cable lifter is to have a hand brake capable of maintaining the holding load, its job being to control and stop the run-out of the chain [1]. LR puts it as capacity sufficient to stop the anchor and chain cable when paying out in a controlled manner [2].
- The clutch separates the two: the cable lifter must be declutchable from the drive, power-operated clutches included, and the on-board test lists clutch functioning as its own item [1][2].
Brake capacity is assessed in a defined condition — single anchor, brake fully applied, cable lifter declutched [2]. Engaged, the drive sits in the load path; declutched, the brake alone carries it.
A windlass also has a separate control or automatic brake criterion, stated against the working load, in addition to the cable-lifter holding load; the two are not interchangeable [1], because working load and chain breaking load are different bases.
The brake number depends on the stopper
ISO 4568 states the split in two clauses: with a cable stopper fitted, the windlass, brakes engaged and cable lifter disengaged, is to withstand 45% of the breaking load of the chain cable without permanent deformation of the stressed parts and without brake slip; without a stopper, 80% [1].
LR states it inside its brake-capacity clause: without a chain cable stopper the brake is to withstand 80% of the specified minimum breaking strength without permanent deformation of strength members and without brake slip; with a stopper, 45% may instead be applied [2]. LR adds the design check: in the holding condition, stress in each load-bearing component is not to exceed the permissible yield under 80%, or 45% with a stopper [2].
What differs is where they lodge the figure. BV NR626 does not print the percentages: it points the brake holding load to NR467, NR483, NR500 and NR600, and allows other values case by case where justified [3]. The CSR write the stopper's 80% in their anchoring-equipment section rather than in a windlass clause [4]. The requirements trace to IACS UR A3, adopted in June 2017, cited by the ClassNK 2018 outline [5]. The common requirement is the split and its condition, not a common clause text; name the document and edition a specification quotes [1][2][3][4].
Two consequences follow. A quotation reading "brake 80%" with no condition attached is incomplete rather than wrong: it describes the no-stopper case. A brake rated at 45% is not weaker by accident; it is rated for a configuration in which a separate device takes the chain load. ISO calls that device a cable stopper and LR a chain cable stopper, a naming difference, not a second device [1][2].
The chain stopper is not a windlass function
A chain stopper is a separate fitting used to secure the anchor chain when riding at anchor, relieving the strain on the windlass, and to secure the anchor in the housed position [6].
Its own requirement is 80%. LR requires stoppers of ductile material, designed to minimise damage to or snagging of the cable, capable of withstanding without permanent deformation 80% of the rule breaking load of the cable passing over them [2]. BV requires a fitted stopper to withstand 80% of the chain's breaking load without permanent deformation of the stressed parts [3]. The CSR, for the bulk carriers and oil tankers they cover, require a stopper on each chain cable, with securing arrangements that withstand 80% without permanent deformation [4].
It carries its own support: LR's allowable-stress table covers windlass and chain stopper supporting structure, but the two are checked against different loads — the windlass structure against the brake holding loads, the stopper against 80% of the rule breaking load [2]. That is why a stopper is not a bracket on the windlass foundation: two devices, two load cases. Its test is separate: BV applies the stopper's design load for 2 min, then inspects visually [3].
A stopper relieves the windlass; it does not rate it. A brake at 45% is rated for a vessel that has one.
What is tested, and where
| Stage | What is covered | What it establishes |
|---|---|---|
| Shop test | No-load running, load test, brake capacity, surveyor witness [2] | The machine runs, carries its duty and holds its rating before shipment. |
| Shop test, brake | Required load for 2 min, cable lifter disengaged, visual check [3] | Brake holding load on the bench, without permanent deformation. |
| On-board test | Braking, clutch functioning, lowering and hoisting, chain riding, hawse and chain pipe transit, stowage, stopper function if fitted [2] | The machine works with this chain, this hawse and this stopper. |
| On-board, speed | CSR trial: mean 9 m/min from 82.5 m to 27.5 m; 3 m/min from design depth to 82.5 m where deeper [4] | Hoisting speed against the trial criterion of that rule set. |
LR requires no-load, load and brake-capacity tests, witnessed by the surveyor; where the works lacks the facilities the load test may move on board and only no-load remains in the works [2]. Brake capacity is to be verified by testing if not by calculation [2], so a calculation file is an acceptable route.
Duration is where the documents part: BV states 2 min, cable lifter disengaged from the prime mover, then a visual check for permanent deformation [3]; LR states no duration in the clause read here [2]. Read a quoted hold time against the rule set it belongs to.
On board, the items are the ones a works cannot check: braking, clutch functioning, lowering and hoisting, chain riding over the cable lifter, transit through hawse and chain pipes, stowage, anchor seating, and stopper function if fitted [2]. Brake capacity here is verified by intermittent pay-out and holding [2].
The CSR trial states a mean speed of 9 m/min from 82.5 m to 27.5 m, and 3 m/min from the design depth to 82.5 m where that depth exceeds 82.5 m [4]; those are CSR trial criteria for the ships that rule set covers. LR states 0.15 m/s, measured with at least three lengths of chain out, 82.5 m, anchor freely hanging, and 3 m/min for deep water [2]. 9 m/min is not a figure to carry across rule sets.
What the nameplate and documents should show
The permanent marking should carry the size designation and the maximum anchorage depth in metres [2][3]. Both LR and BV use 100/3/45 as the example and require the depth alongside it [2][3]: the designation ties the machine to a chain, the depth to a service limit.
Neither marking establishes approval. A nameplate or catalogue entry records what the maker marked and offers; it does not establish class approval, certification scope or performance [2][3].
Three documents carry the rest: the brake-capacity basis, as a percentage of a named chain's breaking load with the stopper condition declared; the test record, stating whether capacity was verified by test or calculation and against which edition; and the foundation, since deck thickness is increased locally in way of the windlass and the supporting structure checked for the brake holding loads [2] — a hull item, not a machine item.
What to send before an RFQ
Six items settle most of a windlass quotation:
- Chain diameter and grade, as they appear in the size designation.
- Chain minimum breaking load, since every brake figure is a percentage of it.
- Whether a chain stopper is fitted, since that decides 45% or 80%.
- The rule set and edition that apply to the vessel.
- Design anchorage depth, which appears on the nameplate and sets the deep-water speed criterion.
- Duty and deck arrangement, including the hawse and chain pipe route the chain has to pass.
The system around the machine is in the anchoring system article; where an anchor or chain is replaced rather than the windlass alone, the interface checks are in the anchor replacement article. Product context sits on the marine windlass and marine chain stopper pages.
Send the six items with the enquiry so that designation, rule set and test record are read together.
References
[1] ISO 4568:2006, Shipbuilding — Sea-going vessels — Windlasses and anchor capstans (sample) — https://cdn.standards.iteh.ai/samples/37153/ee84a317a7a447fe91b01ba084e58552/ISO-4568-2006.pdf
[2] Lloyd's Register, Rules and Regulations for the Classification of Ships, July 2022, Pt 3 Ch 13 Sec 8 — https://www.imorules.com/LRSHIP_PT3_CH13_8.html
[3] Bureau Veritas, NR626 Anchor Windlasses and Chain Stoppers, April 2025 — https://rulesexplorer-docs.bureauveritas.com/documents/nr626/apr2025/626-NR_2025-04.pdf
[4] IACS, Common Structural Rules for Bulk Carriers and Oil Tankers, January 2019, Part 1 Ch 11 Sec 3 — https://www.imorules.com/GUID-AC6535E2-4B3B-4E12-AB63-C3D0F72E4FCA.html
[5] ClassNK, Anchor Windlass Design and Testing — Amended Rules and Guidance, 2018 — https://www.classnk.or.jp/hp/pdf/rules/amendments/e-Amendments/Outline/180629/18-3-43e_outline.pdf
[6] Wärtsilä Encyclopedia, "Chain stopper, cable stopper" — https://www.wartsila.com/encyclopedia/term/chain-stopper-cable-stopper


